Добро пожаловать в HMQY Автозапчасти
What Should Pre-Shipment Inspection Check?
What Should Pre-Shipment Inspection Check?
Last updated 7 November 2026 · Reviewed by the Guangzhou City Hengming Auto Parts Co., Ltd. fitment team · Reading time 4 minutes
Pre-shipment inspection (PSI) takes place when bulk production is 100 percent complete and packed, but before the container leaves the factory. An independent inspector or the buyer’s representative checks quantity, workmanship, fitment features, packaging and labels against the purchase order and approved sample. For exterior auto parts the highest-value checks are visual defects, hole and clip positions, material and wall feel, and carton protection. Catching a defect at inspection saves the cost of returning a container after it crosses the border, where renegotiation becomes much weaker.
Checklist for bumpers, grilles and lamps
| Check | How it is verified | Typical defect found |
|---|---|---|
| Quantity and SKU match | Count cartons, cross-check packing list and OE labels | Short pieces, wrong model mixed in |
| Surface condition | Inspect under even light; count scratches, dents, pinholes, gel coat runs | Scratches, orange peel, filler marks |
| Holes and brackets | Verify sensor cutouts, washer holes, clip bosses, stud positions against sample | Missing or mis-drilled holes, broken clips |
| Fitment features | Compare flange shape, rail and corners against approved sample | Mismatched pre/post facelift version |
| Material and thickness | Caliper wall thickness; inspect cut edge for recycled filler, delamination | Thin skin, recycled PP, delaminated FRP |
| Hardware included | Count clips, brackets, foam, bulbs where listed | Missing accessories quoted in the kit |
| Packing and marking | Carton strength, foam corners, moisture protection, shipping marks and labels | Weak cartons, no mark, damaged corners |
| Colour / finish consistency | Compare approved primer or colour sample across the batch | Gloss or colour drift between cartons |
Timing and standard practice
- Timing: after production reaches about 100 percent and before final packing or container loading.
- Sampling: inspectors commonly use AQL general inspection level II, with major defects accepted at around 2.5 and minor defects around 4.0; the buyer defines the actual acceptance level in the PO.
- Output: a written inspection report with defect photos, pass-or-fail result, and a list of items to correct before release.
- Use: pass means release for loading; fail means rework, replacement or partial shipment before the container moves.
Who arranges the inspection
Buyers usually appoint a third-party inspection company, a QC freelancer, or their own agent in China. Inspection fees depend on inspector person-days and travel to the factory, so the buyer normally pays unless the PO says otherwise. The supplier’s duty is to keep parts ready, provide the approved sample and PO, and allow access. We cooperate with buyer-appointed inspection and share loading photos in parallel; inspection should not be skipped for high-value glass lamps or wide-body kits.
Часто задаваемые вопросы
What is the difference between PSI and factory quality control?
Factory QC checks production internally. PSI is an independent check before shipment, using the PO and approved sample as the standard, which protects the buyer against batch mismatch.
When should inspection be booked?
Ask the supplier for the expected completion date, then book the inspector two to five days ahead so the parts are ready but not yet loaded.
Does the supplier pay for third-party inspection?
Usually the buyer pays, unless the commercial agreement says otherwise. Confirm in the PI who books and who funds the inspection before production.
What defects fail an inspection?
Broken mounting points, missing sensor holes, wrong version, structural cracks, severe surface damage and missing quoted hardware are major failures. Cosmetic dust or light scuff on a primed part may be minor depending on the buyer standard.
Can inspection replace sealing a sample?
No. Inspection compares against a standard, so without an approved sealed sample the inspector has no reliable reference for fitment and finish. Do both: seal the sample, then inspect the bulk.